Kistler has introduced the NCFx electromechanical joining system, a compact range of servo presses designed to provide force and displacement monitoring for industrial assembly operations.
The new Type 2165A system is available in six standardised force ratings from 2 to 80 kN. It combines an integrated strain gauge force sensor with the company’s maXYmos NC process monitoring equipment, allowing joining movements and applied loads to be evaluated during operation.
Kistler has developed the range as a more economical option for manufacturers seeking to replace or supplement conventional hydraulic and pneumatic joining equipment. Its compact configuration is intended for installations where available machine space and integration requirements influence equipment selection.
Electromechanical joining uses a controlled motor drive to generate movement and apply force to the workpiece. A servo amplifier governs the motor according to the required movement and load conditions, allowing the press to follow a programmed joining sequence.
During assembly, the system measures the force applied and the displacement travelled. Together, these measurements provide information about the mechanical behaviour of the parts as they are joined.
A press-fit operation illustrates the value of that information. As one component enters another, the applied force changes according to the dimensions, materials, surface characteristics and alignment of the parts.
The force and displacement relationship can be evaluated against an established process window. An unexpected change in the measured curve may indicate that the components are incorrectly positioned or that the assembly does not correspond to the conditions established during process development.
Monitoring cannot identify every possible defect automatically. Engineers must first determine which measurement characteristics are relevant to the assembly and establish acceptance criteria through suitable trials and validation.
The NCFx uses a strain gauge sensor integrated within the joining module’s housing. The sensor provides force information to the monitoring system, which evaluates the recorded measurements against the configured joining programme.
This differs from the NCFx Pro series, whose available configurations include force sensors integrated directly into the tool holder with digital telemetry. Those features belong to the higher-performance product and should not be assumed to be present in the standard NCFx module.
The new system uses a compact angled design intended to reduce the space required around the joining axis. Its dimensions allow equipment designers to place modules closer together or incorporate them into machines with restricted installation space.
Space constraints can influence the arrangement of automated assembly cells, particularly where several joining heads, workholding devices and component handling systems operate within the same machine.
Reducing the dimensions of the joining module may allow a different equipment layout, but the complete installation must still provide sufficient space for tooling, the workpiece and any required protective systems.
The 2 kN and 5 kN NCFx models provide a 200 mm stroke. Versions rated from 10 to 80 kN have a 400 mm stroke, allowing the equipment to accommodate different joining movements and component dimensions.
Force rating and available travel must both be considered during equipment specification. A press with adequate maximum force may still be unsuitable if its stroke cannot accommodate the required component movement or tooling arrangement.
Kistler reports position repeatability of 0.01 mm for the range. That figure describes the consistency of the equipment’s positioning under the specified conditions, rather than guaranteeing that every finished assembly will achieve a dimensional accuracy of 0.01 mm.
The joining module is driven through a compact servo amplifier communicating with maXYmos NC over EtherCAT. Kistler specifies a communication rate of 4 kHz for the drive and monitoring arrangement.
The digital connection supports the exchange of operating and measurement information without requiring separate analogue connections for every signal. A single-cable motor connection also reduces wiring requirements around the joining module.
Installation and commissioning are further simplified by automatic identification of the connected module. MaXYmos NC imports the relevant sensor and calibration data and configures the servo amplifier.
This reduces the manual parameter entry required when a module is introduced into a machine. The joining programme itself must still be configured for the components being assembled, including movement profiles, force limits and the criteria used to evaluate a completed operation.
An absolute encoder retains positional information after a restart. Referencing is normally required during initial commissioning or following replacement of a relevant component, rather than after every interruption to the power supply.
The NCFx incorporates Safe Torque Off as a standard safety function, with additional functions available as options. These include selected safe motion and braking functions managed through the servo amplifier.
Integrated safety functions can simplify the electrical design of an assembly machine, but they do not remove the requirement to assess hazards across the complete installation. Moving tooling, workpiece handling and operator access must be considered when determining the necessary protective measures.
The monitoring system also supports integration with industrial control equipment through interfaces including PROFINET, EtherNet/IP and EtherCAT. Suitable data interfaces can transfer process and quality records to other systems used within production.
OPC UA provides a further route for making measurement information available for documentation and traceability. Retaining process records can help manufacturers associate individual assemblies or production batches with the force and displacement conditions recorded during joining.
The usefulness of those records depends on maintaining the relationship between the measurement data, the component or batch being processed and the acceptance criteria used to assess it.
Kistler positions NCFx below its more specialised NCFx Pro series, which offers additional sensor options and configurations for demanding assembly processes. The wider joining portfolio covers substantially greater forces, but the standard NCFx range is limited to the six ratings between 2 and 80 kN.
The company’s Assembly Competence Center provides support for selecting equipment and developing joining processes. Trials and simulation can be used to assess the required force, movement, cycle characteristics and expected mechanical behaviour before a manufacturing system is specified.
The new NCFx provides a standardised route into monitored electromechanical joining, combining servo-controlled movement with process evaluation and documentation. Its suitability for individual production operations will depend on the required joining geometry, load conditions, integration arrangements and validated process limits.



