Allient previews industrial I/O and power quality systems

Allient previews industrial I/O and power quality systems

Allient is demonstrating new industrial monitoring and power quality integration. The Boston display previews a BACnet communications module and PointMax energy monitoring, alongside harmonic and motor filters. Spectrum Controls lists the energy module for 2027.


Allient is demonstrating industrial control interface equipment and power quality systems at Automation Fair 2026 in Boston, including a preview of a new BACnet communications module. The 16–19 November programme brings together 5034 PointMax I/O products from Allient Bellevue, operating through Spectrum Controls, and electrical filtering and monitoring equipment from Allient Milwaukee’s TCI business. The exhibits cover different points in the same plant electrical and automation architecture, rather than a single completed installation.

Allient Bellevue’s 5034 PointMax modules provide interfaces between industrial control equipment and field devices. Digital input modules detect machine and sensor states, while digital output modules send commands to connected equipment. Integrating those functions with a programmable controller can allow device information and fault conditions to be managed through the control system. Allient is displaying its available 5034-IV8-SC eight-channel input module and 5034-OV8-SC eight-channel output module alongside products whose release status differs.

The manufacturer will give visitors a first look at the 5034-BACMSTP-SC BACnet communications module. BACnet is used for data exchange in building automation and related control systems, where equipment may need to communicate with different supervisory platforms. A module designed for that interface could connect relevant information into a wider automation environment. The company has not yet supplied a complete public specification identifying every supported object, controller configuration or shipping date, so its detailed interoperability cannot be assumed from the demonstration alone.

The 5034-EM-SC energy monitoring module is also being shown. Spectrum Controls describes a device intended to bring electrical measurements into the distributed PointMax I/O architecture, allowing consumption to be examined at machine, skid, cell or production line level. The supplier’s own product page currently identifies commercial availability as coming in 2027. Its presence at the Boston exhibition therefore represents a preview, not confirmation that the module can already be ordered and commissioned in a production plant.

Machine-level monitoring may allow electrical demand to be related to operating states such as running, idle or stopped, rather than relying only on totals recorded by a factory incoming meter. The proposed system is designed to work with Logix environments and reporting through FactoryTalk Energy Manager. Measurement accuracy, connection arrangements and the limits of available data still need to be checked against released specifications. A detailed baseline is also needed before changes in energy cost or consumption can be attributed to a monitoring project.

Allient Milwaukee is concentrating on the electrical behaviour of variable-speed drives and other nonlinear industrial loads. These systems can draw current in patterns that distort the distribution waveform, while the switched output of an inverter creates rapid voltage transitions at a motor connection. Both effects must be considered when selecting motors, cables, protective devices and power quality equipment. A filter intended to address harmonics on a supply circuit serves a different duty from one designed to condition a drive’s output.

TCI’s HGA HarmonicGuard active filter works by injecting compensating currents to reduce the effects of relevant harmonics. The HGP passive filter uses a selected arrangement of electrical components to attenuate distortion within its designed operating range. The two approaches have different application conditions and should be assessed against the supply network and connected loads. Manufacturer figures for harmonic reduction are product claims, not measurements of the performance of equipment installed at an unnamed customer site.

The display also includes the KMG sine wave filter, V1K dV/dt filter, and KDR line and load reactors. A sine wave filter smooths an inverter’s pulse-width-modulated motor output, whereas a dV/dt filter reduces the steepness of voltage changes that can stress cable and motor insulation. Reactors add inductance to influence current or voltage behaviour depending on where they are installed. Selection is affected by the drive, motor, cable length, switching conditions and the required electrical limits.

TCI is presenting PQconnect monitoring and intelligent control, including a custom Add-On Profile for integration with Rockwell Automation Studio 5000. Bringing filter information into a control system environment can provide operators with access to relevant status and diagnostic values alongside machine information. The available commands, alarms and measurements will depend on the particular connected equipment. Integration does not itself demonstrate compliance with a site’s harmonic requirements or remove the need for commissioning tests.

A new touchscreen kiosk will present filter product lines, engineering drawings and simulations, rather than results from a commissioned factory installation. Such displays can explain how devices respond under modelled conditions; actual performance will depend on the electrical network, loading and installation. Allient has not published a combined trial showing a measurable reduction in energy use or harmonics from deploying all the products now on display together.

Machine-level electricity measurement and drive power conditioning address different engineering problems. The I/O modules, communication interfaces and filtering equipment can sit within the same plant architecture, but each requires its own integration and commissioning checks. Allient has yet to publish full release specifications for the previewed 5034 devices or combined results from a customer installation.


Stories for you


  • Lanes Health links production data across departments

    Lanes Health links production data across departments

    Lanes Health connects nine production lines to shared operational monitoring. FourJaw data is helping engineering, quality assurance and finance teams identify downtime, investigate interruptions and track manufacturing activity.


  • Allient previews industrial I/O and power quality systems

    Allient previews industrial I/O and power quality systems

    Allient is demonstrating new industrial monitoring and power quality integration. The Boston display previews a BACnet communications module and PointMax energy monitoring, alongside harmonic and motor filters. Spectrum Controls lists the energy module for 2027.